Good afternoon, and welcome to the LightPath Technologies Fiscal 2022 third quarter financial results conference call. All participants will be in listen-only mode. Should you need assistance, please signal the conference specialist by pressing the star key followed by zero. After today's presentation, there will be an opportunity to ask questions. To ask a question, you may press star then one on your touch tone phone. To withdraw your question, please press star then two. Please note this event is being recorded. I would now like to turn the conference over to Albert Miranda, Chief Financial Officer. Please go ahead. Thank you. Good afternoon, everyone. Before we get started, I'd like to remind you that during the course of this conference call, the company will be making a number of forward-looking statements that are based on current expectations, involve various risks and uncertainties, including the impact of COVID-19 pandemic, those discussed in its periodic SEC filings. Although the company believes that the assumptions underlying these statements are reasonable, any of them could be proven to be inaccurate, and there can be no assurances that the results would be realized. In addition, references may be made to certain non-generally accepted accounting principles or non-GAAP measures for which you should refer to the appropriate disclaimers and reconciliations in the company's SEC filings and press releases. Following the management's discussion, there will be a formal question and answer session open to participants on the call. I would now like to turn the conference over to Sam, LightPath's President and Chief Executive Officer. Thank you, Al. Good afternoon to everyone, and welcome to LightPath Technologies' Fiscal 2021 Third Quarter Financial Results Conference Call. Our financial results press release was issued after the market closed today and posted at our corporate website. I want to start today's call by providing you a brief update on our company and the vision we have for the future of the business. The area of optics and photonics is at a truly exciting inflection point. Technological advances have made solutions in optics and photonics available and applicable to products and services in a wide variety of industries. Optical solutions are now applicable to products in lidar, drones, augmented and virtual reality, medical field, sporting, and consumer goods, to name a few. An example of one such application is lidar for autonomous drones, for which we recently announced a collaboration with Attollo Engineering. We believe that when a technology like photonics moves from being a specialty technology to being integrated into mainstream industries and applications, our advantages and domain expertise make us an ideal partner for providing the optical engine of our customers' systems. Owning the critical differentiating technologies such as unique materials, high volume molding technology, freeform optics and others, position us to both create unique value for those customers and capture that value in the form of stronger profit margins and long-term agreements, engagements with our customers. Photonics can be embedded in products across many industries. It is estimated to represent as much as 11% of the global economy. The integration of photonics into mainstream products provides us with built-in product and customer diversification opportunities. In the past, LightPath was primarily focused on components within the manufacturing supply chain. That strategy was designed around the premise that photonics is not widely adopted, and therefore the supply chain was highly fragmented and specialized. Today, with the accelerating adoption of photonics into many applications and industries, our strategy is moving away from being simply a component provider to a company focused on providing optical engineered solutions. This means designing and integrating optics, mechanics, electronics, and software to provide the complete optical engine to the customer. We are positioning LightPath to be the partner of choice in this exponentially growing field of optics and photonics. By focusing on our key differentiators, including our design and manufacturing expertise enabled by key optical technologies, low cost, and vertically integrated global manufacturing, we believe we can be a leading OEM to customers across the globe. One area where adoption of photonics is accelerating is the growing need and benefit of infrared imaging. Improvement in infrared imaging are opening up new applications to an existing technology across short-wave, mid-wave, and long-wave infrared imaging. Further applications are being applied in border surveillance, drones, maritime and coastal surveillance, and critical infrastructure projects. Infrared imaging has, for the most part, been based on the use of germanium as the optical material. However, germanium comes primarily from China and Russia, with the U.S. importing as much as 95% of the germanium it uses. An alternative to germanium is chalcogenide glass, which we name BlackDiamond Glass. Through our ongoing production of our BlackDiamond 6 glass, BD6, we have gained over the last few years significant experience in making and using those materials, positioning us as probably the lead manufacturer for this kind of material in the U.S. Further, receiving the exclusive license to commercialize further chalcogenide glasses developed by the Naval Research Laboratory positions us as the only true source for a portfolio of materials that provide an alternative to germanium. To that end, I recently traveled to Washington, D.C., to give a talk about the subject, followed by meetings with DoD and government officials on the topic. We are beginning to see that owning this key technology is well aligned with the growth of infrared imaging and the efforts to build a resilient and robust supply chain in the U.S. An important effort that is further emphasized by the recent geopolitical events, all of which reinforces our strategy and indicates that we are in the right place, in the right time, and most importantly, heading in the right direction. To reiterate this, it is owning critical technologies that positions us to capture much of the value in those growing markets. The essence of our strategy revolves around technologies that are critical to the implementation of optical system in those areas and leveraging those to develop and deliver optical systems and subsystems that produce better infrared images with an overall lower cost of ownership to the customer. Even as commercialization is happening more broadly, there remains a large addressable market for government and military applications. Our unique technology and expertise with producing and processing the infrared materials, including fabrication of the components and assemblies, lower cost manufacturing in our ITAR-approved facility in Latvia, and technological advancements like our diamond-like carbon DLC coating process, which has been qualified for all U.S. military application, places us in a leading position in this market. We believe our value proposition makes us an increasingly important partner to commercial development of engineered solutions for Department of Defense agencies, Defense Industrial Base, DIB, prime contractors, and other infrared optical imaging businesses. In October 2021, we announced our entry into the freeform optics arena. Freeform optics involves lenses with surface shapes that lack certain symmetrical attributes, which makes them more challenging to mass produce but provide improved aperture, field of view, and miniaturization. Freeform optics are becoming a key element in applications such as augmented and virtual reality, AR and VR, infrared and military optical systems, and 3D imaging and visualization. Many times these systems require the higher performance and more compact form factor that freeform optics can provide, allowing increased flexibility and overall size, weight, and power optimization. The qualities of the material used are the key to producing smaller and lighter augmented and virtual reality glasses that look more like conventional eyeglasses and less like the bulky AR/VR goggles of today. Additionally, with freeform optics, lidar systems can achieve larger fields of view and lower losses, which in turn translate to higher resolution images and ability to extend detection distances. The adoption of freeform optics in such applications has been limited due to the manufacturing technologies that previously made glass mass commercialization cost prohibitive. We believe that our technology solves for that. In January of this year, we announced that our freeform optics won the 2022 Prism Award for Manufacturing, which is an annual international competition that honors the best optics and photonics products on the market. In March, we announced that Attollo Engineering chose our freeform optics for use in its lidar products. Attollo's line of laser range finders and lidar products provide fast measurement with high accuracy and precision in an ultra-compact package. We integrate our molded freeform optics in their systems, which allows them to achieve optimum performance while minimizing the number of optical components. Our freeform optics reduce the cost and weight of their system. At the same time, we continue working with more customers on developing freeform optics for their applications and continue working on eight large high opportunity applications which are in different stages of development and qualification. This is truly an exciting time to be working in photonics and optical solutions. We believe the application of the technologies we use will continue to grow as costs are reduced and product acceptance increases. We're really excited about the progress the company has made and the direction we're going in. We have endured several hurdles over the past year or two, but believe that we are on firmer footing now, and we're at the point where applications for our technology solutions are beginning to be more mainstream. I will also provide a brief update on the ongoing situation in China before making concluding remarks. As we have mentioned before, although we have taken steps to minimize the business impact from the termination of the previous management employees and transition to new management personnel in our China subsidiary, we have experienced some short-term adverse impacts on domestic sales in China and the results of operations in the three-month period ending June 30, 2021, and the nine-month period ending March 31, 2022. These adverse impacts have significantly declined, yet management anticipate they may still have some effects in the next quarters. Domestic sales in China are also being impacted by COVID-19 related shutdowns, which have not directly impacted our factory, but have impacted the operations of some of our Chinese customers. Lastly, I would like to thank all LightPath employees and stakeholders who are working every day to grow the business and achieve breakthrough products and technologies. This concludes my prepared remarks. Now I will pass the call over to Al Miranda, our CFO, to review financial results for the first quarter. Thank you, Sam. I'd like to remind everyone that much of the information we're discussing during this call is also included in our press release issued earlier today and will be included in the 10-Q for the period. I encourage you to visit our website at lightpath.com. I will discuss some of the primary financial performance metrics and provide additional color on them to better assist investors in analyzing the company. As a reminder, we had been significantly impacted by the transition of business conditions in China during the fourth quarter of fiscal 2021 and into the fiscal year. LightPath's third quarter financial results are also negatively impacted by expenses associated with the management employee transition in our Chinese subsidiaries. Although to a lesser extent than in recent quarters. The consolidated basis revenue for the third quarter of fiscal 2022 was $8.3 million, compared to $10.7 million in the year ago period. Sales of infrared products were $3.7 million or 45% of the company's consolidated revenue in the third quarter of fiscal 2022. Revenue from the PMO products was $4 million or 48% of consolidated revenue. Revenue from specialty products was $547,000 or 7% of total company revenue. The decrease in revenue from sales of infrared products is primarily due to a decrease in sales to customers, excuse me, in the industrial market and for temperature sensing applications, which peaked in demand during the third quarter of fiscal 2021. PMO sales increased 3% in the third quarter of fiscal 2022, compared to the third quarter of fiscal 2021. Since the drop-off of PMO sales in the fourth quarter of 2021, sales of PMO products in China have improved sequentially each quarter of fiscal 2022. Driven in part by other telecommunication customers as well as an increase in sales to customers in the industrial and commercial industries. Increased sales in specialty products were primarily due to NRE projects for customers in the industrial and defense industries during the third quarter of fiscal 2022. I wanna take a moment to expand on the revenue topic. As Sam alluded to earlier, revenues from China for the first three quarters have been recovering. However, our lack of sales growth is still related to disruptions in China. Revenue is down fiscal year to date versus last year to date in China by $5.1 million. Outside of China, primarily in the U.S. and Europe, our sales are up by 8% or $1.6 million. We do see a China recovery on the horizon as bookings are coming back to pre-transition levels. However, with the recent wave of COVID shutdowns, it's difficult to determine precise shipping dates, as Sam mentioned earlier. Further to the revenue discussion, we have taken a strategic approach regarding the quality of revenues. First, we started the process of sunsetting certain specialty products that are no longer part of our growth plans. Second, we've taken a more targeted approach to annual volume contracts regarding pricing, which has had the anticipated effect of reducing volume but increasing the average selling price on the contracts and hence our margins. Moving on to margins. I'd like to remind listeners that PMO margins are typically higher due to our molding technology and capabilities, which enable mass production and a more automated machine process. Infrared diamond turned lenses historically have lower margins due to the extra manual production step. With the growth in our molding technology as applied to infrared products being made from our proprietary BD6 material, the margins will increase over time from both the advantages of the material cost and using the automated molding process. Gross margin in the third quarter of fiscal 2022 was approximately $3 million, compared to approximately $3.9 million in the same period of the prior fiscal year. Gross margin as a percentage of revenue was 37% for the third quarter of fiscal 2022, compared to 36% for the same period of the prior fiscal year. The increase in gross margin as a percentage of revenue is primarily due to product mix. Favorable product mix resulted in slightly higher gross margins as a percentage of revenue, despite the lower revenue level in the third quarter of fiscal 2022. As we transition the business to engineered solutions, we would expect margins to increase over time. This is due to several factors, including multiple lenses required for an assembly, as Sam did describe. Selling general and administrative costs were approximately $2.6 million for the third quarter of fiscal 2022, a decrease of approximately $187,000 or 7% compared to the same period of the prior fiscal year. The decrease in SG&A costs is primarily due to decrease of approximately $149,000 of expenses associated with the previously described events that occurred in our Chinese subsidiary, including legal and consulting fees. Although certain legal activities are ongoing, the related costs have leveled off and should cease by the end of this calendar year. New product development costs were approximately $590,000 in the third quarter of fiscal 2022, a decrease of approximately $50,000 or 8% as compared to the prior fiscal year. Net loss for the third quarter of fiscal 2022 was approximately $495,000 or $0.02 basic and diluted loss per share, compared to $223,000 or $0.01 basic and diluted loss per share for the third quarter of fiscal 2021. The decrease in net income for the third quarter of fiscal 2022 as compared to the same period of the prior fiscal year was primarily attributed to lower revenue and gross margin, partially offset by lower operating expenses. Additionally, we recognized $210,000 of other income in the fiscal third quarter related to the reversal of accruals following the China investigation. It was determined that a Chinese subsidiary would not be responsible for those expenses and the reversal is recognized as a gain. We believe EBITDA is helpful for investors to better understand our underlying business operations. Our EBITDA for the three months ended March 31, 2022 was approximately $647,000, compared to $1.1 million for the same period of the prior fiscal year. The decrease in EBITDA in the third quarter of fiscal 2022 was primarily attributable to lower revenue and gross margin, again, partially offset by the aforementioned $210,000. As of March 31, 2022, we had working capital of approximately $11 million in total cash and cash equivalents of approximately $5.2 million. More than 50% of our cash and cash equivalents was held by our foreign subsidiaries. Cash provided by operations was approximately $352,000 for the first nine months of fiscal 2022, compared to approximately $3.1 million for the same period of the prior fiscal year. The decrease in cash flows from operations in the first nine months of fiscal 2022 is due to the decrease in net income and a decrease in accounts payable and accrued liabilities, partially offset by a reduction in inventory. We also renegotiated an amendment with BankUnited, extending our term loan until April of 2024. The extension further strengthens our intermediary financing abilities and enables us to continue along our strategic path. Our total backlog at March 31, 2022 was approximately $19.7 million, an increase of 1% as compared to $19.5 million as of March 31, 2021. Compared to the end of fiscal 2021, our total backlog decreased by 8% during the first nine months of fiscal 2022. The decrease in backlog during the first nine months of fiscal 2022 is largely due to timing of the renewal of a large annual contract for infrared products. Consistent with prior years, we received the renewal of this contract in the fiscal second quarter and began shipping against that contract in the fiscal third quarter. As a reminder, it is customary for our backlog to fluctuate during the year because of the timing of bookings of orders and annual renewals from our customers. With this review, our financial highlights and recent developments discussion has concluded. I'll now turn the call over to the operator to begin the question and answer period. We will now begin the question and answer session. To ask a question, you may press star then one on your telephone keypad. If you are using a speakerphone, please pick up your handset before pressing the keys. To withdraw your question, please press star then two. Once again, that was star then one to ask a question. At this time, we will pause momentarily to assemble our roster. Our first question will come from Gene Inger of ingerletter.com. Please go ahead. Hi, Sam and Al. It sounds like, An interesting quarter, obviously still in the turnaround mode. Excuse me. I think it looks like SG&As were actually lower, but it also looks like unit profits dropped, did they, for both PMO and infrared? Yeah. T he units fluctuate all the time, and it's really dependent on the mix. We began to see some of the larger customers in China, especially in telecom, come back to some degree, as we discussed last quarter. Those tend to be lower unit prices on them. In the infrared, it's very significant. Engineered solutions and assemblies can be in hundreds of dollars sometimes, where individual components can be in tens of dollars or less. We tend to steer away from giving too much importance to the average sale prices fluctuation, since the mix of products and what we do has been varying considerably more. But yeah, thanks for noticing the G&A and the effect. I think that all things considered, given the $8.3 million top line, the results are pretty good. The continued improvement in gross margins, even when top line hasn't grown really in that specific quarter, is very encouraging. Right. That causes me, Sam, to ask this. The market cap is so low. Of course, there's hundreds of companies that are pummeled into almost oblivion at this point. A, it looks like you'll make it through this. B, you've been pointing in the right direction, but you're trading at around 1x sales, and you would think from an investor standpoint, that's very cheap. Now maybe I'm just giving an opinion, and I don't know whether you actually want to eventually shop the company for a sale or some sort of a merger. Isn't it essentially undervalued based on even a reasonable growth? Yeah. I think, first of all, I agree with you, that, in my, independent opinion, that it's undervalued and, an attractive investment. T he public company, we're always open for all options, and we never rule out anything. We're not actively shopping the company around. We think that we're, as you said, heading in the right direction. A lot of the indications are that we're doing the right thing. Sometimes it's a matter of timing. I t happened to be that our discovery of the multi-year effect in China happened at a time where the market was rallying, and so we didn't enjoy as much of that rally. Now our recovery is happening at a time where the market is down in a bear market. Sometimes it's just as simple as that. I guess my last question for the moment, so others can come on, which might be if you have a lot of experience in China. You turned around and built a big company there in an earlier life. I wonder whether you envision growing China or eventually with this new focus with the Navy and so on and on freeform optics. I enjoyed your discussion, which is on YouTube, in Washington. I wonder whether you would eventually drop China, spin it off somehow and concentrate on the domestic scene, which seems to be doing better for the company. Yeah. Definitely our investment approach has changed considerably in the last two years since I joined. We stopped investing in China even before all of those events. We rerouted really all of our investments to the Latvia operation, which serves the U.S. by being an ITAR facility, and now to Orlando, where we're essentially doubling our manufacturing space and bringing manufacturing back. That said, the operation we have in China is still very important. It's a good cash generator for us. It's our core technology, which we wouldn't spin off because that would essentially include giving away the technology, but we still see it as a valuable piece of the company, just not our strategic long-term focus as much. Do you have a timeline and I'll let you go. Do you have a timeline on when you envision the new licenses with the Navy and so on, and AI and VR, actually, and you talked about some of that. Do you have a timeline when you think this will crystallize into bookable business? Yeah, two separate things, right? The Navy, the licensing of the Navy materials, as I mentioned, really one thing we've seen from the discussions I've had in Washington and with different government officials and such, is that we're really at a perfect timing from that sense. The U.S., through the Defense Production Act and through the executive order of the Biden administration on the resilience of supply chain, is heavily investing in developing a manufacturing base in the U.S. and accelerating readiness of new technologies, increasing local capacity and such. The U.S. currently imports, as I mentioned, 95% of its germanium. That is $2.7 billion roughly, of germanium a year. A quarter of that goes into optics. Around $600-$700 million of germanium goes into optics in the U.S. Chalcogenide is at a perfect spot to substitute that. It's not a one-to-one substitution, and you'll not completely eliminate germanium, but we're definitely the best option at this point for the U.S. in terms of reducing the dependence on China and Russia for that material. Accelerating that is a key element of many stakeholders, including some of our prime customers who are seeking to be involved in helping us accelerate that and bring those materials to market. We're anticipating that in the next few months, the first material might be already released. We're currently already working on prototypes, and we're working with some of the primes also on designing the material lens, seeing the encouraging results that we have. It's really a key element here, I think, in much of what the U.S. is looking at. In terms of the freeform optics, that's a bit of a different play in the sense that this is a technology that we've already developed and matured enough. Now is the time for the customers to take that in and to utilize it. We've mentioned the last month that Attollo Engineering, for example, has already adopted freeform optics into their lidar products, and it looks very promising and successful. They have some very unique products in the sense of being able to very quickly monitor the location of drones, of fully autonomous drones, making sure they don't collide with others and so on. The freeform optics are really a key element there. In other places, we've shipped prototypes already to AR companies, for example, have already our freeform optics in prototypes. Others are at different stages of it. Lidar is becoming a bigger piece there. That will take longer because most of those are, the freeform optics is enabling a cutting-edge application to such a degree that that application needs to first be adopted and win its own commercial success before the freeform can scale up with it. It looks very encouraging. Yeah. I don't wanna- Go ahead, Gene. Well, to see if you have time for one quick. You didn't give any color. Sure. In your opinion on two areas that I was interested in in the past. One was low Earth orbiting satellites, such as a SpaceX system, which there's even talk about China wanting to intercept that and so on. I'm wondering, speaking of intercepting, whether you're involved in that and whether you're involved with the new laser interception systems in Israel, which use infrared and laser to try to intercept enemy rockets. Yeah, yeah. Obviously, as someone who grew up in Israel, I'm very proud of that system, of seeing it. I can't comment on specific systems and technologies, of course. I can say our business with Israel has grown exponentially in the last half a year or so, and I feel very good about it. In a great part, it is because of the investments we made in the Latvia operation, enabling them to really service customers from there far, far better than we could before. We're involved in multiple low-Earth orbit and space projects, all the way from optical communication projects to thermal cameras and for detection cameras. Definitely, mid-wave cameras are playing a major role today in detecting supersonic missiles through low-Earth orbit. The government and the Pentagon have decided to revoke money just recently. It was in the news to deploy a whole satellite network related to that. That's a very exciting application that we see for mid-wave. Another place where chalcogenide glass plays a major role, it's really being athermal and very low weight compared to alternatives, makes it a great material for any space applications, especially low-Earth orbiting camera systems. Thank you. I appreciate the enlightenment. I hadn't heard anything lately from you about that. Absolutely. Yeah. We also just to, you know, close the loop on that. We have announced previously that we have grants from Space Florida, from the European Space Agency and a couple of other projects and such, all related to accelerating our technologies for use in space, especially all the chalcogenide materials, to replace germanium and to be used in very specifically low-Earth orbiting satellites. I suppose as a footnote to that, you could mention whether ISP Optics, your Latvia operation, is involved with the drones that are going to Ukraine now or coming from Turkey, and whether or not you see a surge in business in Europe as a result of this. I'd say that, you know, we don't know where our products end up always. I can definitely say that we proudly deliver products to multiple UAV and drone companies that, hopefully make good use of it. I can say that our expansion in Latvia, adding the optical coatings there, making it vertically integrated and independent of U.S. manufacturing in that sense, aligns perfectly in timing to all the increases in defense budgets in Europe now and to a increase in demand that we are seeing already in terms of designing our products into defense applications. The Latvia operation, besides being an ITAR operation, can also serve European defense companies now by being completely vertically integrated, having the coating and assembly capabilities there, which is something that we're confident is gonna deliver significant growth in Europe for us in the infrared imaging. Thank you, sir. Absolutely. Good to hear from you, Gene. Once again, if you would like to ask a question, please press star then zero.